Разпродажба!

AC Mains Line Power Filter LPF-6000

 624.00 696.00 Incl. VAT
 520.00 580.00 Excl. VAT

LPF-6000 AC Mains Line Filter

Описание

Базирайки се на големия успех на своите предшественици DC Блокер в метална кутия и Комбинирания DC Блокер и Синфазен филтър, предлаганият тук Линеен мрежов филтър допълнително развива техните силни страни и продължава напред, добавяйки нови характеристики и възможности.

Блок-схема на флитъра:
As it is shown on the Block-Schematic below, LPF-6000 has a двустепенна структура на синфазните филтри плюс DC Блокер от нова генерация (DC Blocker NG).

Block-Schematic of LPF-6000 AC Mains Line Power Filter

Синфазният филтър от първата степен е изпълнен с индуктивност CMT-8121 на Triad Magnetic. Тя е сертифицирана за макс. ток 20A и следователно отговаря на изискваният за захранване на повечето съвременни крайни стъпала. Филтърът от първата степен работи в два режима - "синфазен" и "диференциален", като по този начин ефективно намалява и двата вида смущения.
On the same PCB is placed the DC Blocker NG (New Gen) – because of the new approach used in this module, its DC blocking capabilities are raised up to 4.5V while retaining the same power throughput as its predecessors.
As it’s shown on the Block-schematic and on the pictures of the unit, LPF-6000 has 6 AC Mains outlets and the mutual impact of each other is greatly diminished by use of dedicated second-stage EMI/RFI Filters for each output. The second-stage filters utilize the Wuerth Electronics’ с висококачествени сърцевини от нанокристалин. Благодарение на техните параметри е възможно изработването на нискочестотни филтри с достатъчно ниска честота на среза, същевременно запазвайки честотна характеристика без резки пикове в началото на региона на непропускане.
Последната платка в набора се използва за защита от пренапрежения (гръмотевизи, токови удари и т.н.) и управление на релето за включване/изключване на устройството.
Както може да се види от блок-схемата, за защита от пренапрежения се използва група от варистори, включени след централния предпазител, намиращ се във входния IEC конектор.
Централният превключвател за включване/исключване е разположен на задния панел и служи за командване на на висококачествено реле, което комутира мрежовото напрежение след IEC конектора.

Опроводяване:
As probably everyone knows, the proper wiring is crucial to reveal the full unit’s performance. That’s why special attention is paid to the process of design and physical wiring of the LPF-6000 power filter.
Концепцията за топологията "звезден център" е широко застъпена тук - на снимките ясно се виждат трите "звездни центъра" - за линиите на Фаза, Нула и Защитно заземяване Първите два са изпълнени с клемни редици, монтирани на платката с DC Блокера и първата степен на филтъра против смущения, докато третият е изпълнен с Нулева разпределителна редица, свързана към дъното на металната кутия.

Кутия:
LPF-6000 is enclosed in steel sheet case, high-quality black powder coated. Beneath the case are placed 4 solid aluminum feet with rubber dampening rings.
On the front side is mounted solid hard anodized aluminum panel with red LED indicator for normal operation.

Dimensions: 430x310x80 mm. (WxDxH)
Тегло: approx. 6 kg.

Лицевите панели могат да бъдат черно и сребристо анодирани

 

On the back side panel are placed 6 AC Outlets (various types are available), IEC inlet with fuse holder and ON/OFF switch.

Back panel with 6 Schuko AC Outlets, C14 IEC inlet and ON/OFF switch

Вариации:
In most cases along with the low-power audio devices (DACs, Network streamers, CD players etc.) there are power amplifier(s) which draw much more power than the second stage EMI/RFI filters can provide. That’s why, a variation with only four second stage filters is available.
Block-Schematic of LPF-6000 with two power outputs is shown below:

LPF-6000 with two power AC outputs

 

The first two AC outlets are connected directly to the output of the high power first stage EMI/RFI filter and are dedicated for high-power consumers.

LPF-6000 with two direct (high-power) outputs

 

There are customers who prefer a variant with ON/OFF relay circuitry bypassed and the input IEC inlet directly connected to the first stage filter+DC Blocker board:

LPF-6000 without Relay Switch Board

This variant of the filter is also useful for the cases when higher than normal handled power is needed, if C20 IEC inlet is directly connected to the DC Blocker & First stage EMI/RFI board, the filter is capable to withstand up to 15A.

The LPF-6000 line power filter can work with various input AC voltages and frequencies – the widespread 230V/50Hz and 115V/60Hz are supported off-the-shelf (just leave a note for the required type during the checkout process). If your input AC Mains voltage is different than the above-mentioned ones, send us a question for confirmation via the site’s contact form and we’ll discuss the possibilities for filter’s manufacturing.
The different AC Mains input voltages goes along with the different AC outlets used in the countries all over the world. We’re happy to announce that LPF-6000 supports wide variety of AC outlets: Standard EU Schuko, French, UK, US, Australian and Switzerland types.

Submit your review
1
2
3
4
5
Submit
     
Cancel

Споделете отзив

LPF-6000 AC Mains Line Filter
Усреднен рейтинг:  
 1 reviews
 by Ildefonso
Very pleased

This power filter is awesome!! It improves your Hi-Fi system lowering the mains noise and the transformer hum. The customer service is top notch.

Допълнителна информация

Тегло 6.5 кг
Тип на изходните контакти

EU Schucko, French, UK plug, US plug, Australian, Switzerland

Input AC inlet type and Relay Switchboard presence

C14 IEC/Relay Board present, C14 IEC/Relay Board NOT present, C20 IEC/Relay Board NOT present

Брой вторични синфазни филтри

4 filters + 2 HP outputs, 6 EMI/RFI filters

Front Panel Color

Silver, Black